8 inch ford rear end identification.

Yes, axle lengths are an issue. 9 3/8 have a different spider pinion offset and so the axle lengths are different from an otherwise identical 9 inch. Here is a 66 example that I posted in the past: On a 66 galaxie 9 inch the axles are 32 1/4 on the right and 29 19/32 on the left but the 9 3/8 is 31 7/8 on the right and 29 13/16 on the left.Location. Colorado. They never put a big bearing under an EB until like 74 or 75. A 60's vintage EB will have a 9" in the rear with most likely a Dana 30 up front. If the tag on the 9" is gone and so is the VIN tag, then there really isnt a way to tell what the gears are without opening it up.Mailing List. Ford 8 and 9 Inch Rear Ends. Complete - Ready to Run - Drop out third members for Ford rear ends. New Timken bearings, Yukon Gear ring and pinion gears. Ratios for every need, whether it's for street, highway, circle track or towing. Third members for any Ford or Mercury using a removable carrier.Ford 8.8 axle. The Ford 8.8 is an automotive axle manufactured by Ford Motor Company at the Sterling Axle Plant in Sterling Heights, MI. It was first used in model year 1983 Ford trucks. The axle was developed to replace the Ford 9-inch axle. This axle is still in production today for a variety of Ford vehicles.

1966 Ford Mustang Axle Information & Ratios. The first table is the code and gear ratio. If you know your axle tag number, simply go to the second table. Axle code: Ratio & type: 6: 2.80 open differential: F: 2.80 locking differential: 2: 2.83 open differential: B: 2.83 locking differential: 1:

You also need to be aware of axle offset which is 2-3/8". While I have not tried, been led to believe up to 66 Ford backing plates/brakes will work, so you should …

It looks like a 9 inch, but is smaller. The 9 (and 8) inch have a solid axle housing, there is no inspection cover at the rear. The 9 (and 8) inch rear ends are known as a drop out, because the entire 3rd member (carrier aka pumpkin) comes out of the front of the housing as a unit. All the Dana's, Ford 8.8's have inspection covers, as do the ...Literally fell out on the track. IMO, unless you have a nodular case, Detroit locker and the big pinion support, the strength of the ford 9" is over-rated. In my experience, a typical 2 rib or WAR case 9" with the small pinion support, like you find in a wrecker, isn't as strong as a 12 bolt. falcongeorge,Dec 9, 2015.The BOM stamp (2) or Axle Identification Tags (2A) are used to identify Dana axles / differentials. The BOM will identify the model number, the gear ratio, the type of axle / differential, and component parts. Traditional BOMs are 6 digits followed by 1 or 2 digits, and start with the numbers 60 or 61. On some tags, the first 2 digits won't ...Ford Rear End Catalog: Hot to Select Axle & Measure the Companion Flange: Your Source for Classic / Late Model Auto Parts: INFO 404-767-3378 FAX 404-305-9437: CONTACT METRO: ... Note all 8 inch units use 28 spline axles. 28 Spline Axle: 31 Spline Axle: Note the concave oval area in center of axle flange.

Gear ratio refers to the number of rotations the driveshaft makes compared to the number of rotations the axle makes. In Ford 8.8 axles, this ratio determines the torque and speed delivered to the wheels. Choosing the right gear ratio for your specific needs and vehicle application is essential. A lower gear ratio provides more torque for off ...

Find great deals on eBay for ford 8 inch rear end used. Shop with confidence. Skip to main content. Shop by category. Shop by category. Enter your search keyword ... FORD 8 inch 2.79 OPEN REAR END ID TAG MUSTANG. Opens in a new window or tab. Pre-Owned. C $41.02. gwpford (8,479) 99.5%. Buy It Now +C $46.04 shipping.

Mr Gasket 142 Rear End Differential Gasket, Ford 8.8 Inch. $17.37 /each. $19.30. Add to Cart. Speedway Motors | #91031935. Weld-On Rear Disc Brake Kit, 1969-77 GM Caliper, 1.96 Inch Backspace (1) Position: Rear. Bolt Pattern: ... Ford 9-Inch Housing Identification and Axle Measurement. Read More.The Ford 9.75" Rear End The 9.75" rear end is the old war horse of the two available rear ends for the 2015-2020 F150s. The good news is that the 9.75" is extremely distinct in how it looks, and in our experience, is the more common of the two differential options. The 9.75" has a very noticeable taper the goes toward the passenger's side of ...Ford Rear Axle Assembly Identification - Page 01 - FORDification.com . Reactions: sheza65. Save Share. ... I should have a 3.00 rear end and according to the Ford specifications for 1967 a three speed manual with a 3.00 rear end would have to be a limited slip differential only. The only thing I can make is that the number they have doesn't ...Aug 30, 2011 ... The "88" indicates 8.8 inch ring gear diameter. ... You can place a mark on the pinion yoke and have someone rotate the rear wheel 1 revolution ...How to Measure Ford Rear End Axle Splines, Flange Width and Height Metro Auto Parts Market: Ford Rear End Catalog: Hot to Select Axle & Measure the Companion Flange ... Therefore, the only foolproof way is to remove the axle and count. Note all 8 inch units use 28 spline axles. 28 Spline Axle: 31 Spline Axle: Note the concave oval area in ...If you need the 9" for the strength/power - then by all means use it. But you don't need that much rearend -- so the 8.8 properly built is a better choice. Just went through all this in selecting a new rear end to replace the Volvo unit in mine. Chose an 8.8 out of a Lincoln; Moser 31 spline axles; c-clips eliminated; 3.55 gears; TrueTrack LSD ...

8-Inch Ford Rear End Torque Specifications. The 8-inch Ford rear axle was used from the early 1960s to 1980 in small and mid-size passenger cars with six- and small-block V-8 engines. The 8-inch rear axle looks very much like the popular Ford 9-inch rear axle. Both axles use a third member that contains the differential, which is made up of the ...Ford 9 inch rear end identification is easy and can be accomplished with nothing more than a deep socket as a “go-no-go” gauge for the bottom two retaining nuts on the center section. If the socket fits (as shown in our photo below) it is a Ford 8-inch housing. The 9-inch housing’s center section will not allow the socket to clear, and ...1977 Ford Axle Codes: Below is a axle code chart from 1977: There's no question, the easiest way to identify the axle and gear ratio in your truck is from the door sticker. If you open the drivers door and look at the door jamb, you'll see a sticker like the one shown below: You'll see that the area labeled (F) is for the Axle Code.Ford Rear End Catalog: Hot to Select Axle & Measure the Companion Flange: Your Source for Classic / Late Model Auto Parts: INFO 404-767-3378 FAX 404-305-9437: CONTACT ... Therefore, the only foolproof way is to remove the axle and count. Note all 8 inch units use 28 spline axles. 28 Spline Axle: 31 Spline Axle: Note the concave oval …Ford 975 rear end diagramFord 8 inch diff identification Ford inch identification diff rear explorer axle differential cover swap sourcePosi trac inch pinion lok. Ford 10.25" & 10.5" Rear Axle - Differential Parts Catalog - West Coast1310 U-Joint Series is the most common U-Joint ever used. It is still used on OE applications. 1.062 cap and 3.219 width. (1 1/16 x 3 1/4 close) 1330 U-Joint Series is very common and used on OE production. 1.0625 cap and 3.622 width. (1 1/16 x 3 5/8) 1350 U-Joint Series is used on trucks mostly for OE.8 Inch axle length. Hey all, I'm taking the old rear end out of my 62 Falcon and putting in a 8". the problem I'm having is the axle is correct for the drivers side, but too short for the passenger side. I need to buy a new axle for the pass side but am wondering if there are different 8 inch rearends or was there only one size made.

Google Ford 9 inch assembly videos and you will get a series of You Tube videos (4) called AutoRestoMod which take you through the whole process using common tools and no press. Very good for the first timer. Sounds like you need it. Also check out the Tom's Differentials video for some very detailed instruction on an all-out performance 9".Ford 8.8 Inch. Ford 8.8 Inch Rear End Ring and Pinion Gears. We offer the most complete line of rear end parts for the Ford 8.8 inch differential, this differential was utalized by Ford as early as 1981 in the F-100 pickup, Broncos in 1981 to 1984, E150 Vans starting in 1983. Mercury's including Capri and Cugars starting in 1986.

Ford Rear Axle Assembly Identification - Page 05. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL. or. L.Ford Rear Axle Assembly Identification - Page 04: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: WDM-E: Ford Pickup '63-'72 F-100: 3.25: 9 in: NL: 28-WDM-F: Ford Pickup '63-'72 F-100: 3.50: 9 in: NL: 28-WDM-H:Now, many know that the early 9" rear ends are the same length as the 65/66 8", with most sites stating 52.25" from the outside of the housing flange to outside flange. However, the Kevinstang info states that this measurement is actually from the INSIDE of the flange to flange. My 9" measures 52.25" from inside to inside, which means the ...Mar 26, 2020 ... 28 Spline You must remove one axle from the rear end to identify the spline count. wrap a piece of paper around the teeth to count the teeth ...USA. Do a search for ROTTEN LEONARD here on the HAMB. He has redrilling kits available to change from one bolt pattern to another. They are listed for sale in the CLASSIFIEDS and he offers a Hamb discount. According to the advrtising the redrilling can be done with out removing the axle from the housing (with the rearend still in the car).Cracker289. 1272 posts · Joined 2002. #8 · Aug 1, 2011. Agree with 2ManyStangs especially, I have enough 8's and 9's in my playpen to know right off the bad, that picture is an 8. You can it's sort of "flat' along the bottom, if you looked straight at it from the rear it would appear "oval" whereas a 9 will appear perfectly round.Part 5 of project Mut - Rear End Upgrade is the first to go back onto the build. This one is long as it is step by step and done with the help of Mark a sea... Axles Tubes Are 4-Inches. Applications: Ford Used The Dana 70 And Dana 70HD Axles In F-350 Trucks Up To 1985.5. The Ford 10.25-Inch Rear Axle Replaced The Dana 70 After 1985. Ford Also Equipped The 1980-Current E-350 Dual Rear Wheel And Some E-450 Super Duty Vans With Dana 70 or Dana 70HD Rear Axles. Likes: 8. Received 205 Likes on 165 Posts. Ford 9 Inch Rear End Traction Lock Identification. I am trying to find a complete 9 inch center section for my 65 Mustang's Lincoln rear end. I need one that has traction lock. From the pictures I have found online a 9 inch traction lock looks nothing like the traction lock in my F150's 8.8.1966 Ford Mustang Original 289. Edelbrock RPM Performer Heads; bored .30 over. Weiand Stealth Intake, Holley 600 CFM Carb. Comp Cam 268H 9.5:1 Speed Pro Pistons. Patriot Tri-Y Headers w/ 2.5" H Pipe, Flowmaster 40S. Air ride system with 4 link CSRP Front Disk Brakes. Ford 8 3.40 trac-loc rear end.

2010-2011 Ford Ranger 8.8-inch Axle - 58.50 inches *. 1991-2003 Ford Explorer 8.8-Inch Axle - 59.625 inches. * The 2010-2011 Ford Ranger 8.8-inch axle is actually narrower and has shorter shafts than the 2009 and earlier models. Ford used rear disc brakes on the 2010-2011 Rangers, so Ford Shortened the axle housing and shafts to compensate for ...

The pinion nut does not have a specific torque rating for itself, you tighten it tight enough to get a certain pinion preload (measure by an inch/lb torque wrench or dial). With old pinion bearings the preload is supposed to be 8-14in/lbs, with new pinion bearings it needs to be 16-28in/lbs. Now, I'm not totally sure on this, but I'm pretty ...

RAT-4114 - solid bearing spacer - 1 each (makes the pinion preload easier to set up) FEL-912A616 - axle gaskets - 2 ea. TMK-41322 - axle seal - 2 ea. You're also going to need an inch pound torque wrench- needle type (click type will not give accurate reading), they're about $20 at Orielly or Autozone. Like.The BOM stamp (2) or Axle Identification Tags (2A) are used to identify Dana axles / differentials. The BOM will identify the model number, the gear ratio, the type of axle / differential, and component parts. Traditional BOMs are 6 digits followed by 1 or 2 digits, and start with the numbers 60 or 61. On some tags, the first 2 digits won't ...According to Nasty Z28, the GM/Chevrolet 12-bolt rear end was manufactured from 1965 through 1971. After that, GM instituted the "Corporate" rear end, a 10-bolt rear end that integrated feartures of both the 10- and 12-bolt rear ends. Rear ends with measurement designations are named after the diameter of the ring gear, i.e. 7.2 and 8.5 inch.Ford identification axle differentials inch rear history torino brake member third 1962 items lowerFord rear end axle f100 housing 1957 spline inch 4x4 member chevy traction differential loc 3rd truck identify center 1960 Fabricated 9 in ford rear axle w/ posi traction 3rd member, 58 inFord 9 rear axle housing.Need help with your differential identification? Call Sierra Gear & Axle at (800)792-2714. Our differential experts are available from 8am to 5pm PST Monday thru Friday. Found your application and need parts? Locate a Sierra Gear & Axle Distributor near you, or call (800) 792-2714. AAM 9.25″ Dodge RAM '03-'13 Front.Ford Differentials. The Ford 8.8- and 9-inch rear differentials are two of the most popular and best-performing differentials on the market. While the 8.8-inch differential is commonly used in late-model Mustangs, the 9-inch is the more popular and arguably the most dominant high-performance differential for muscle...ive got a 68 mustang 289 auto with an 8 inch out back. im converting it to a 9 inch to accommodate the new engine mods. Ive got the chunk and everything but i dont know if i can use the brake backing plates from the 8 inch and for my new 9 inch. -69 Mustang - 351W AFR 185, Vic Jr, .512 @ 232°, 750 Holley, WC T5, 4.30 TruTrac, CalTracs.

Ford Rear Axle Assembly Identification - Page 02. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL. or. L.Rear ford end inch identification axle mustang help ranger diff differences between guide forums trucks tech 1995 axles 0lFord 8.8 rearend durability and strength Narrowed moparThe 9-inch ford rearend is the strongest rearend out there—it's all due.Ford axle history and identification: ford differentialsFord 9 inch identification Ford axle code chart3.73 dana 60 score. Check Details Ford 9 inch rear end tag decoder. How to find out the axle ratio on a ford pickupFord rear end/differential identification Ford 9" : what year i have to locate parts?Differential diagrams.Being a 28 spline axle standard case(not a nodular iron one) your carrier bearing size is likely the most common average size but some out there like for the 1966-77 Ford Bronco used smaller id bearings and some full size Ford cars used larger od bearings. 2.892" od carrier bearings with the 1.780" id are the most common.Instagram:https://instagram. packwoods x runtz banana kushmission bbq reviewfox 45 news anchors daytonfox 11 news los angeles anchors 1962 Falcons were not built with 8 inch rear differentials. I would find out where this 8 inch diff came from. perhaps measure the diff for fitment. I would suspect the 8 inch diff would be from a Maverick Ford car. F-350 DRW Diesel w/5th wheel RV. Voedsephobia is the fear of garbage disposals.NEW 8 INCH NODULAR FORD REAR END TRU TRAC POSI, MUSTANG, MAVERICK OR STREET ROD. Opens in a new window or tab ... 88 watchers. Ford Mustang or Maverick ORIG 8" REAR END AXLE ID TAG 2.79. Opens in a new window or tab. Pre-Owned. $25.00. initialchi (1,874) 100%. or Best Offer +$4.00 shipping. Ford 8 Inch Open Carrier Mustang Maverick Pinto Falcon ... chitterlings saleeunice city jail roster Description. F8TL - Ford 8" Inch Trac Lok Posi Unit. -Ford 8" 28 spline trac lok posi unit. -100% new, not remanufactured. Traction-Lok differentials optimize your vehicle's traction by transferring the power to both rear wheels.Not really much of a difference, just the 9.75 has larger carrier and pinion bearings so can take more of a load. The truck 8.8 has large wheel bearings and axles like a 9.75 so they can carry more weight than a car 8.8. Either one is a solid reliable axle. Reply Like. # 4. best way to level up in madden 23 The differential bearing cap bolts are 55-70 ft-lbs for a 8" rear differential. The differential bearing cap bolts are 70-85 ft-lbs for a 9" rear differential. All below specs are for 8" and 9" differentials. Differential bearing adjusting lock nut bolts: 12-25 ft-lbs. Carrier to housing stud nuts: 25-40 ft-lbs.The Ford 8.8-inch axle has a cast center section and the internal components are installed from the rear. ... This is 2.25 inches for the Ford 9-inch and 1.5 inches for the 8.8-inch axle. Identification Tag. ... This is an example of the brakes that fi t the small wheel end bearing for a 10 x 2-inch-wide drum brake on the left and a 10 x 1¾ ...The Ford 9.75" Rear End The 9.75" rear end is the old war horse of the two available rear ends for the 2015-2020 F150s. The good news is that the 9.75" is extremely distinct in how it looks, and in our experience, is the more common of the two differential options. The 9.75" has a very noticeable taper the goes toward the passenger's side of ...